713-270-8520

AEM Cold Air Intake, 03-05 Neon SRT-4

Read or Write Review

Model Number: 220100

Pull in colder air for more power with the AEM cold air intake!

This intake runs from the turbo, around and in front of the battery, then down into the wheel well. The filter sits low enough to pull cooler air that is not heated by the engine, for maximum power. This intake was tested on a relatively stock SRT-4 and gained a peak of 8 horsepower and 13 lbs of torque. At 4400rpm our car gained 12 horsepower and 14 lbs of torque at the wheels!

This AEM cold air intake is available in polished, red and silver. (Blue is now discontinued, no more left!) This intake was revised back around 2007 from a two piece aluminum intake kit to a aluminum upper and lower plastic ducting. The plastic ducting fits better than the old aluminum lower ducting. It also includes an aluminum shield to protect the filter from water and debris.

Utilizing full 3 inch piping, this intake can flow way more air than most other air intakes. It also uses a 3 inch dry flow air filter. There is no cutting needed to install this intake. It's a bolt on intake, and comes complete with couplers, clamps and installation instructions.

Option

$349.99

AEM Cold Air Intake, 03-05 Neon SRT-4, Air Intake: Store Name

Ask a Product Question

- *E-mail: (Required)
  *Name: (Required)
  
  Characters remaining: 500
  Our Q&A program is designed to educate our community.
  This is not to answer questions about your orders, or problems you are having with a part you ordered. If you have questions about a part you have already ordered, please contact us by email at info@modernperformance.com or call us 713-270-8520 for faster service.
Anonymous

Once I purchase an AEM cold air intake for a 05 SRT-4 will I have to replace the MAS as well?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- Modern Performance
  
  There is no need to replace your stock MAP sensor with this intake. In fact, there is nothing else needed during, or after install. Its very straightforward, and comes with instructions. Simiple hand tools are all thats needed, ie, 8mm, 10mm, 13mm sockets, phillips screwdriver.
Phil

Does this cold air intake offer more of a horsepower increase over the short ram intake?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- Modern Performance
  
  Yes the cold air system will give you a slight gain over a short ram.
nathan

i noticed in the picture of the intake installed it is all polished but the picture of the kit itself only shows half of it polished is there an option for all polished

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- Modern Performance
  
  AEM only offers what we supply in the picture. If you wanted something all poilished im sure you would have to get that custom made somewhere.
Brandon

Just wondering if there is any way to get just the splash shield.
Thanks.

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- customer service rep
  
  We used to be able to offer spare parts, however, AEM now requires all customers to contact them directly for replacement parts. Link for their contact information: https://www.aemintakes.com/contact-us
David

i had a short ram aem intake but just ordered a new turbo from yall, gt30r. which one would be better if any difference, this aem cai or the agp intake?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- customer service rep
  
  Both are great air intakes and are very similar in design. the only benefit of the AGP is that if you have a 4 inch inlet turbo, then you can get the AGP intake with a 4 inch elbow whereas the AEM has a 2.5 inch reducer to bolt onto the factory turbo.
Steve

Is this intake legal in California? Does it have carb numbers?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- customer service rep
  
  Yes, this intake, along with the AEM short ram intake systems are both CARB approved.
Max

Will this kit work with a stock 2 1/2 inch factory turbo inlet or do I need to buy an adapter separately?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- customer service rep
  
  This intake was specifically designed for use with the factory turbo, there is nothing else needed. If you have a larger NON OEM turbo that uses anything other than a 2.5 inch id, then you'll need a different coupler at that point.
Chelsey

How much clearance will this intake have to the wheels? My car is very low, maybe 6"-8" clearance from the hole in the fender to the tire (no wheel wells). Will it fit?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- customer service rep
  
  This intake does not sit the filter lower than the bottom of the bumper. Plus, it comes with an aluminum splash shield so its well protected.
Jeramy Brewer

is there somewhere to mount the vacuum solenoids

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- Customer Service Rep
  
  Yes of course. You can see the aluminum bracket in the parts photos, and the solenoids mount to the battery tray with it.
Jason

Will this clear the DC Sports strut tower brace? Was that the fitment adjustment from '06?

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- Customer Service Rep
  
  Yes, this clears all strut braces made for the Neon SRT-4. There is no fitment issues with this intake with any other combination of parts. The revision in 2006 was to make this intake with the lower plastic duct instead of the lower duct being made in aluminum. This allows the intake to fit better with the plastic duct due to clearance issues in the fenderwell.
David Palfalvi

what are the dimensions of the filter itself? Trying to get a pre filter for water

1 Answer
- E-mail: Name: (optional)
  
  Characters remaining: 500
  Type your response below:
- Customer Service Rep
  
  You can find more about the air filter used in this kit by searching for AEM 21-203DK. Here are the specs anyways:
  
  Air Filter Material Non-woven Synthetic
  Air Filter Shape Tapered Conical
  Base Outside Diameter 6 in (152 mm)
  Flange Length 1.5 in (38 mm)
  Flange Inside Diameter 3 in (76 mm)
  Height 5.125 in (130 mm)
  Top Outside Diameter 5.125 in (130 mm)
  Air Filter Large End Diameter 6 in (152 mm)