{"title":"03-10 PT Cruiser Turbo-Interior \u0026 Gauges-OBDII Scan Gauges","description":"","products":[{"product_id":"aeroforce-interceptor-gauge-03-05-neon-03-05-pt-cruiser","title":"Aeroforce Interceptor Gauge, 03-05 Neon \/ 03-05 PT Cruiser","description":"\u003cp\u003e\u003cb\u003eThe Scangauge, is a very special type of instrument gauge that connects within seconds to your cars OBD2 port, located right below your dashboard.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe OBD2 port is a diagnostic port that is used for dealerships, service stations, and even emissions testing facilities to connect a computer to your car to see how your cars running, problems with your car, etc. Because the OBD2 port communicates lots of different parameters of your engine, you can view tons of information! Furthermore, it will not interfere with the OBD2 ports operation, because it simply plugs in, and is not hardwired, and no wires are cut, chopped or soldered for the gauge to work!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThis gauge lights up red.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eHere's a listing of some of the many different engine parameters that can be viewed with this gauge.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM\u003c\/li\u003e\n\u003cli\u003eMPH\u003c\/li\u003e\n\u003cli\u003eIntake Air Temperature (post Intercooler)\u003c\/li\u003e\n\u003cli\u003eEngine Coolant Temperature\u003c\/li\u003e\n\u003cli\u003eBattery Voltage\u003c\/li\u003e\n\u003cli\u003eLong Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eShort Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eO2 Sensor Voltage\u003c\/li\u003e\n\u003cli\u003eManifold Pressure (vacuum\/boost) displayed in PSI\u003c\/li\u003e\n\u003cli\u003eIgnition Advance\u003c\/li\u003e\n\u003cli\u003eKnock Retard\u003c\/li\u003e\n\u003cli\u003eFuel Status (open\/closed loop)\u003c\/li\u003e\n\u003cli\u003eThrottle Position Percentage\u003c\/li\u003e\n\u003cli\u003eEngine Load\u003c\/li\u003e\n\u003cli\u003eAbility to check AND ERASE ENGINE CODES\u003c\/li\u003e\n\u003cli\u003eAbility to record engine parameters for 60 seconds and review parameters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe Interceptor gauge is 52mm (2 1\/16\") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePlease note: Aeroforce is no longer shipping these guages with the metal U shaped bracket for mounting. They claim that they found almost all customers are using pods that dont require the metal U shaped bracket, and so they are no longer shipping these gauges with that bracket and nuts. If you are mounting this gauge into a pod, we would recommend using electrical tape around the body of the gauge for additional friction to hold it more tightly into the pod upon insertion.\u003c\/b\u003e\u003c\/p\u003e","brand":"Modern Performance","offers":[{"title":"Default Title","offer_id":42989039550542,"sku":"601640","price":274.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0688\/2902\/0238\/files\/564_10898_popup_4a06ccb3-4591-4d76-bd81-cce8109c73e4.jpg?v=1766116326"},{"product_id":"aeroforce-dual-interceptor-gauge-03-05-neon-03-05-pt-cruiser","title":"Aeroforce Dual Interceptor Gauge, 03-05 Neon \/ 03-05 PT Cruiser","description":"\u003cp\u003e\u003cb\u003eThe Scangauge, is a very special type of instrument gauge that connects within seconds to your cars OBD2 port, located right below your dashboard.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe OBD2 port is a diagnostic port that is used for dealerships, service stations, and even emissions testing facilities to connect a computer to your car to see how your cars running, problems with your car, etc. Because the OBD2 port communicates lots of different parameters of your engine, you can view tons of information! Furthermore, it will not interfere with the OBD2 ports operation, because it simply plugs in, and is not hardwired, and no wires are cut, chopped or soldered for the gauge to work!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWe only stock these gauges with a RED display. Other color options may be available by special order.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eHere's a listing of some of the many different engine parameters that can be viewed with this gauge.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM\u003c\/li\u003e\n\u003cli\u003eMPH\u003c\/li\u003e\n\u003cli\u003eIntake Air Temperature (post Intercooler)\u003c\/li\u003e\n\u003cli\u003eEngine Coolant Temperature\u003c\/li\u003e\n\u003cli\u003eBattery Voltage\u003c\/li\u003e\n\u003cli\u003eLong Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eShort Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eO2 Sensor Voltage\u003c\/li\u003e\n\u003cli\u003eManifold Pressure (vacuum\/boost) displayed in PSI\u003c\/li\u003e\n\u003cli\u003eIgnition Advance\u003c\/li\u003e\n\u003cli\u003eKnock Retard\u003c\/li\u003e\n\u003cli\u003eFuel Status (open\/closed loop)\u003c\/li\u003e\n\u003cli\u003eThrottle Position Percentage\u003c\/li\u003e\n\u003cli\u003eEngine Load\u003c\/li\u003e\n\u003cli\u003eAbility to check AND ERASE ENGINE CODES\u003c\/li\u003e\n\u003cli\u003eAbility to record engine parameters for 60 seconds and review parameters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe Interceptor gauge is 52mm (2 1\/16\") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThis gauge works with:\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e2003-2005 Dodge Neon (does not work with 2000-2002 Neons)\u003c\/li\u003e\n\u003cli\u003e2003-2005 Dodge SRT-4\u003c\/li\u003e\n\u003cli\u003e2001-2010 Chrysler PT\/GT Cruisers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePlease note: Aeroforce is no longer shipping these guages with the metal U shaped bracket for mounting. They claim that they found almost all customers are using pods that dont require the metal U shaped bracket, and so they are no longer shipping these gauges with that bracket and nuts. If you are mounting this gauge into a pod, we would recommend using electrical tape around the body of the gauge for additional friction to hold it more tightly into the pod upon insertion.\u003c\/b\u003e\u003c\/p\u003e","brand":"Modern Performance","offers":[{"title":"Default Title","offer_id":42989041483854,"sku":"601640-DUAL","price":439.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0688\/2902\/0238\/files\/584_10907_popup.jpg?v=1762488235"},{"product_id":"aeroforce-interceptor-gauge-07-12-caliber-06-12-pt-cruiser","title":"Aeroforce Interceptor Gauge, 07-12 Caliber \/ 06-12 PT Cruiser","description":"\u003cp\u003eIntroducing a new version of Aeroforce Inteceptor Scangauge.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThe Scangauge, is a very special type of instrument gauge that connects within seconds to your cars OBD2 port, located right below your dashboard.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe OBD2 port is a diagnostic port that is used for dealerships, service stations, and even emissions testing facilities to connect a computer to your car to see how your cars running, problems with your car, etc. Because the OBD2 port communicates lots of different parameters of your engine, you can view tons of information! Furthermore, it will not interfere with the OBD2 ports operation, because it simply plugs in, and is not hardwired, and no wires are cut, chopped or soldered for the gauge to work!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThis version of scangauge, is feature wise exactly the same as the previous gauge, except now it has a series of interchangeable faces and bezel.\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eHaving interchangeable faces and bezels makes it easy to change the look of your gauge within seconds. Now you can choose any combination of white face\/black face, and silver bezel, black bezel!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFurthermore, you can piece together custom faces for your gauge set with a red \"SRT\" logo! Add the faces in the color you want and the SRT overlay to create a matching look for your interior!\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"Aeroforce Interceptor Scan Gauge\" src=\"https:\/\/www.modernperformance.com\/images\/aeroforcesrtfaces.jpg\" height=\"188\" width=\"500\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThis gauge lights up green, just like the factory gauge cluster lettering\/lighting.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eHeres a listing of some of the many different engine parameters that can be viewed with this gauge.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM\u003c\/li\u003e\n\u003cli\u003eMPH\u003c\/li\u003e\n\u003cli\u003eIntake Air Temperature (post Intercooler)\u003c\/li\u003e\n\u003cli\u003eEngine Coolant Temperature\u003c\/li\u003e\n\u003cli\u003eBattery Voltage\u003c\/li\u003e\n\u003cli\u003eLong Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eShort Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eO2 Sensor Voltage\u003c\/li\u003e\n\u003cli\u003eManifold Pressure (vacuum\/boost) displayed in PSI\u003c\/li\u003e\n\u003cli\u003eIgnition Advance\u003c\/li\u003e\n\u003cli\u003eKnock Retard\u003c\/li\u003e\n\u003cli\u003eFuel Status (open\/closed loop)\u003c\/li\u003e\n\u003cli\u003eThrottle Position Percentage\u003c\/li\u003e\n\u003cli\u003eEngine Load\u003c\/li\u003e\n\u003cli\u003eAbility to check AND ERASE ENGINE CODES\u003c\/li\u003e\n\u003cli\u003eAbility to record engine parameters for 60 seconds and review parameters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe Interceptor gauge is 52mm (2 1\/16\") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eA function menu is available by pushing both buttons simultaneously. One menu option allows you to enter a record mode. Once selected, the Interceptor will return to normal scan mode, but will start recording the displayed data automatically when the throttle exceeds 60%. Approximately 60 seconds of data will be stored. Returning to the menu screen, you can choose to replay the stored data on the Interceptor display.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. This way you can monitor several items without taking any other actions.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eHigh intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live without it!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eAnother menu option offers the ability to swap the foreground and backround colors of the display. Using this feature, for example, the gauge with a black backround and blue characters (negative image) becomes a blue backround with black characters (positive image). Not only can this be visually appealing but beneficial in changing lighting conditions. Positive images are easier to read in bright sunlight, negative at night.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe Interceptor's scan rate can also be adjusted through a menu function.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eDTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. has been inadvertently left disconnected, or something was just not put back together properly.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe two analog inputs can be configured through menu choices. A linear conversion can be entered so that an analog signal connected to the gauge can be read in appropriate units. These inputs are handy for pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air\/Fuel ratio kits, etc. These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe gauge has bi-directional controls allowing for manaul control of the low and high speed fans.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eLast but not least, the Interceptor will measure 0-60 times, as well as 1\/8 and 1\/4 mile time and speeds. This is accomplished through a simple menu selection.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eInstallation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. Literally plug-and-play!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eTop shows Instant Miles Per Gallon (MPG)\u003cbr\u003e\u003cbr\u003ebottom shows Throttle percentage.\u003cbr\u003e\u003cbr\u003e\u003cimg border=\"0\" src=\"https:\/\/www.modernperformance.com\/images\/interceptor3.jpg\" height=\"186\" width=\"191\"\u003e\u003c\/p\u003e\n\u003cp\u003eTop shows Short Term Fuel Trim, Bottom shows RPM\u003cbr\u003e\u003cbr\u003e\u003cimg border=\"0\" src=\"https:\/\/www.modernperformance.com\/images\/interceptor2.jpg\" height=\"186\" width=\"191\"\u003e\u003c\/p\u003e\n\u003cp\u003eTop shows Coolant, Bottom shows Catalytic Temperature\u003cbr\u003e\u003cbr\u003e\u003cimg border=\"0\" src=\"https:\/\/www.modernperformance.com\/images\/interceptor4.jpg\" height=\"186\" width=\"191\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eLight output for this Aeroforce Interceptor Scangauge is Green.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePlease note: Aeroforce is no longer shipping these guages with the metal U shaped bracket for mounting. They claim that they found almost all customers are using pods that dont require the metal U shaped bracket, and so they are no longer shipping these gauges with that bracket and nuts. If you are mounting this gauge into a pod, we would recommend using electrical tape around the body of the gauge for additional friction to hold it more tightly into the pod upon insertion.\u003c\/b\u003e\u003c\/p\u003e","brand":"Modern Performance","offers":[{"title":"Black","offer_id":42989045055566,"sku":null,"price":274.0,"currency_code":"USD","in_stock":true},{"title":"Silver","offer_id":42989045088334,"sku":null,"price":274.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0688\/2902\/0238\/files\/564_10898_popup.jpg?v=1762488235"},{"product_id":"aeroforce-dual-interceptor-gauge-07-12-caliber-06-10-pt-cruiser","title":"Aeroforce Dual Interceptor Gauge, 07-12 Caliber \/ 06-10 PT Cruiser","description":"\u003cp\u003eThis Dual Interceptor Gauge is designed to work with a number of Chrysler, Dodge and Jeep vehicles including:\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e07-12 Dodge Caliber\u003c\/li\u003e\n\u003cli\u003e08-09 Dodge Caliber SRT-4\u003c\/li\u003e\n\u003cli\u003e06-10 Chrysler PT Cruiser\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThis is the DUAL setup of Aeroforce Interceptor Scangauges famous gauge. This Dual gauge setup will allow you to monitor 4 lines of parameters whereas the single gauge setup will show 2 lines of parameters.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eWe are proud to introduce the Aeroforce Interceptor gauge. This gauge installs easily and quickly by plugging into your OBD2 port under your steering wheel. This means you can install this gauge with NO special tools, no cutting, no soldering, and in most cases have it wired up and running within 25 minutes!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM\u003c\/li\u003e\n\u003cli\u003eMPH\u003c\/li\u003e\n\u003cli\u003eIntake Air Temperature (post Intercooler)\u003c\/li\u003e\n\u003cli\u003eEngine Coolant Temperature\u003c\/li\u003e\n\u003cli\u003eBattery Voltage\u003c\/li\u003e\n\u003cli\u003eLong Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eShort Term Fuel Trim\u003c\/li\u003e\n\u003cli\u003eO2 Sensor Voltage\u003c\/li\u003e\n\u003cli\u003eManifold Pressure (vacuum\/boost) displayed in PSI\u003c\/li\u003e\n\u003cli\u003eIgnition Advance\u003c\/li\u003e\n\u003cli\u003eKnock Retard\u003c\/li\u003e\n\u003cli\u003eFuel Status (open\/closed loop)\u003c\/li\u003e\n\u003cli\u003eThrottle Position Percentage\u003c\/li\u003e\n\u003cli\u003eEngine Load\u003c\/li\u003e\n\u003cli\u003eAbility to check AND ERASE ENGINE CODES\u003c\/li\u003e\n\u003cli\u003eAbility to record engine parameters for 60 seconds and review parameters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eGauges are available with Black and White faces and Silver and Black Bezels. The Displays lettering will show in RED.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFurthermore, you can piece together custom faces for your gauge set with a red \"SRT\" logo! Add the faces in the color you want and the SRT overlay to create a matching look for your interior! Be sure to purchase two of each for dual gauge sets.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg width=\"350\" height=\"121\" src=\"https:\/\/www.modernperformance.com\/images\/aeroforcesrtfaces.jpg\" border=\"0\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe Interceptor gauge is 52mm (2 1\/16\") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eA function menu is available by pushing both buttons simultaneously. One menu option allows you to enter a record mode. Once selected, the Interceptor will return to normal scan mode, but will start recording the displayed data automatically when the throttle exceeds 60%. Approximately 60 seconds of data will be stored. Returning to the menu screen, you can choose to replay the stored data on the Interceptor display.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. This way you can monitor several items without taking any other actions.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eHigh intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live without it!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eAnother menu option offers the ability to swap the foreground and background colors of the display. Using this feature, for example, the gauge with a black background and blue characters (negative image) becomes a blue background with black characters (positive image). Not only can this be visually appealing but beneficial in changing lighting conditions. Positive images are easier to read in bright sunlight, negative at night.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe Interceptor's scan rate can also be adjusted through a menu function.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eDTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. has been inadvertently left disconnected, or something was just not put back together properly.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe two analog inputs can be configured through menu choices. A linear conversion can be entered so that an analog signal connected to the gauge can be read in appropriate units. These inputs are handy for pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air\/Fuel ratio kits, etc. These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eThe gauge has bi-directional controls allowing for manual control of the low and high speed fans.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eLast but not least, the Interceptor will measure 0-60 times, as well as 1\/8 and 1\/4 mile time and speeds. This is accomplished through a simple menu selection.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eInstallation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. Literally plug-and-play!\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHere are some photos of the Interceptor in use on a 08 Caliber SRT4.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eTop shows Instant Miles Per Gallon (MPG)\u003cbr\u003ebottom shows Throttle percentage.\u003cbr\u003e\u003cbr\u003e\u003cimg width=\"191\" height=\"186\" src=\"https:\/\/www.modernperformance.com\/images\/interceptor3.jpg\" border=\"0\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eTop shows Short Term Fuel Trim, Bottom shows RPM\u003cbr\u003e\u003cimg width=\"191\" height=\"186\" src=\"https:\/\/www.modernperformance.com\/images\/interceptor2.jpg\" border=\"0\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eTop shows Coolant, Bottom shows Catalytic Temperature\u003cbr\u003e\u003cimg width=\"191\" height=\"186\" src=\"https:\/\/www.modernperformance.com\/images\/interceptor4.jpg\" border=\"0\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eLight output for this Aeroforce Interceptor Scangauge is Green.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePlease note: Aeroforce is no longer shipping these guages with the metal U shaped bracket for mounting. They claim that they found almost all customers are using pods that dont require the metal U shaped bracket, and so they are no longer shipping these gauges with that bracket and nuts. If you are mounting this gauge into a pod, we would recommend using electrical tape around the body of the gauge for additional friction to hold it more tightly into the pod upon insertion.\u003c\/b\u003e\u003c\/p\u003e","brand":"Modern Performance","offers":[{"title":"Black","offer_id":42989047644238,"sku":"601641-DUAL-2","price":439.99,"currency_code":"USD","in_stock":true},{"title":"Silver","offer_id":42989047677006,"sku":"601641-DUAL-1","price":439.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0688\/2902\/0238\/files\/584_10907_popup_a779e964-c266-4fa5-8e04-1146dc2dace6.jpg?v=1762488235"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0688\/2902\/0238\/collections\/529_5870_popup_404d9285-2ab1-4155-8603-f88daf54180d-9499951.png?v=1762487048","url":"https:\/\/www.modernperformance.com\/collections\/01-10-chrysler-pt-cruiser-03-10-pt-cruiser-turbo-interior-gauges-obdii-scan-gauges.oembed","provider":"Modern Performance","version":"1.0","type":"link"}