Secure logos

:: Newest Products

Vibrant Header without CAT 05+ Cobalt /05-07 SS Supercharged
Vibrant Header without CAT 05+ Cobalt /05-07 SS Supercharged
$569.99

:: Currencies


::
Aeroforce Dual Interceptor Gauge 03-05 Neon / 03-05 PT CruiserModel: 601640-

$389.99

Available Options:
Add SRT Faceplate:

This Dual Interceptor Gauge is designed to work with a number of Chrysler, Dodge and Jeep vehicles including the:

  • 03-05 Dodge Neon
  • 03-05 Dodge Neon SRT
  • 03-05 Chrysler PT Cruiser.

    This is the DUAL setup of Aeroforce Interceptor Scangauges famous gauge. This Dual gauge setup will allow you to monitor 4 lines of parameters whereas the single gauge setup will show 2 lines of parameters.

    We are proud to introduce the Aeroforce Interceptor gauge. This gauge installs easily and quickly by plugging into your OBD2 port under your steering wheel. This means you can install this gauge with NO special tools, no cutting, no soldering, and in most cases have it wired up and running within 25 minutes!

  • RPM
  • MPH
  • Intake Air Temperature (post Intercooler)
  • Engine Coolant Temperature
  • Battery Voltage
  • Long Term Fuel Trim
  • Short Term Fuel Trim
  • O2 Sensor Voltage
  • Manifold Pressure (vacuum/boost) displayed in PSI
  • Ignition Advance
  • Knock Retard
  • Fuel Status (open/closed loop)
  • Throttle Position Percentage
  • Engine Load
  • Ability to check AND ERASE ENGINE CODES
  • Ability to record engine parameters for 60 seconds and review parameters.

    This version of scangauge, is feature wise exactly the same as the previous gauge, except now it has a series of interchangeable faces and bezel.
    Having interchangeable faces and bezels makes it easy to change the look of your gauge within seconds. Now you can choose any combination of white face/black face, and silver bezel, black bezel! Light output for this Aeroforce Interceptor Scangauge is red.

    Aeroforce Interceptor Gauge A function menu is available by pushing both buttons simultaneously. One menu option allows you to enter a record mode. Once selected, the Interceptor will return to normal scan mode, but will start recording the displayed data automatically when the throttle exceeds 60%. Approximately 60 seconds of data will be stored. Returning to the menu screen, you can choose to replay the stored data on the Interceptor display.

    The gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. This way you can monitor several items without taking any other actions.

    High intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live without it!

    Another menu option offers the ability to swap the foreground and backround colors of the display. Using this feature, for example, the gauge with a black backround and blue characters (negative image) becomes a blue backround with black characters (positive image). Not only can this be visually appealing but beneficial in changing lighting conditions. Positive images are easier to read in bright sunlight, negative at night.

    The Interceptor's scan rate can also be adjusted through a menu function.

    DTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. has been inadvertently left disconnected, or something was just not put back together properly.

    The two analog inputs can be configured through menu choices. A linear conversion can be entered so that an analog signal connected to the gauge can be read in appropriate units. These inputs are handy for pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air/Fuel ratio kits, etc. These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus.

    The gauge has bi-directional controls allowing for manaul control of the low and high speed fans.

    Last but not least, the Interceptor will measure 0-60 times, as well as 1/8 and 1/4 mile time and speeds. This is accomplished through a simple menu selection.

    Installation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. Literally plug-and-play!

    Heres a photo showing the dual Aeroforce setup along with a 95 Neon with complete SRT4 swap including instrument SRT4 cluster. This shows the color combination of the Aeroforce setup along with the SRT4 cluster. Aeroforce Interceptor Scan Gauge Here are some photos of the Interceptor in use on a 08 Caliber SRT4.

    Top shows Instant Miles Per Gallon (MPG)
    bottom shows Throttle percentage.
    Aeroforce Interceptor Scan Gauge

    Top shows Short Term Fuel Trim, Bottom shows RPM
    Aeroforce Interceptor Scan Gauge

    Top shows Coolant, Bottom shows Catalytic Temperature
    Aeroforce Interceptor Scan Gauge

    Light output for this Aeroforce Interceptor Scangauge is red.

    Available Options:
    Add SRT Faceplate:
  • Current Reviews: 2
    This product was added to our catalog on Friday 30 October, 2009.
    Reviews
    Customers who bought this product also purchased
    AEM UEGO Digital Air/Fuel Ratio Wideband Gauge
    AEM UEGO Digital Air/Fuel Ratio Wideband Gauge
    MPx 3-Inch O2 Housing 03-05 Neon SRT / 03+ PT Cruiser GT
    MPx 3-Inch O2 Housing 03-05 Neon SRT / 03+ PT Cruiser GT
    Energy Suspension Bushing Kit 95-05 Neon
    Energy Suspension Bushing Kit 95-05 Neon
    Currently viewing:  Aeroforce Dual Interceptor Gauge 03-05 Neon / 03-05 PT Cruiser - Aeroforce Interceptor Gauges

    :: Shopping Cart

    0 items